How to measure a euro cylinder

Two measurements, taken from the centre screw in the door edge to each face of the door. Get them in the right order and almost nothing else about buying a cylinder can go wrong.

Written by admin_marko, last updated 20 November 2026

A euro cylinder is described by two numbers, like 30/50. They are the lengths of the two halves in millimetres, measured from the centre of the fixing screw to the outside face of the door and from the same screw to the inside face. Getting those two numbers is a two minute job with a tape measure, and it is the single thing that decides whether a cylinder or a cylinder based smart lock will fit your door.

What you need

A tape measure or a steel rule, and the ability to open the door. Nothing else. You do not need to remove anything.

The measurement, step by step

1. Open the door and look at its edge

On the edge of the door, where it meets the frame when closed, there is a metal plate with the latch and usually a bolt coming through it. That is the faceplate. Somewhere in the middle of it, below the latch, there is a single screw head pointing straight at you. That screw passes through the lock body and into a notch in the cylinder, and it is the only thing holding the cylinder in place.

2. Measure from that screw to the outside of the door

Put the end of your tape on the centre of that screw and measure horizontally to the outside face of the door, the side with the keyhole that faces the street or the hallway. Do not measure to the edge of the handle plate or the escutcheon. Measure to the face of the door itself. Write that number down. It will almost always be somewhere between 30 and 60 millimetres.

3. Measure from that screw to the inside of the door

Same screw, same tape, now measuring the other way to the inside face. Write that number down too.

4. Write them outside first

This is where most mistakes happen. The two halves are usually different lengths, and a cylinder ordered the wrong way round sticks out on the street side and sits recessed on the inside, which is both ugly and a security problem. Our convention, and the one most European suppliers use, is outside / inside. So a cylinder written 40/30 is 40 mm on the street side and 30 mm inside. If you are ordering from anyone and you are not completely sure which convention they use, write it out in words.

What if the door has a handle plate over the cylinder?

Measure to the face of the door, not to the face of the plate, and then measure the thickness of the plate separately and tell us. Some escutcheons are three millimetres thick and some are twelve, and that changes which length finishes flush.

Why the length matters more than you would expect

There are two failure modes, and they are not symmetrical.

A cylinder that is too short will not reach far enough for the cam to engage properly or for the key to turn freely. This is annoying and obvious. You will know immediately, and you will send it back.

A cylinder that is too long works perfectly, and that is the problem, because you will leave it there. Anything protruding more than about three millimetres past the handle or escutcheon gives a tool something to grip. Snapping an over-length cylinder is a recognised method of forcing a door, it is fast, it is quiet, and it is specifically something insurers ask about when a claim is made. The correct length finishes flush or very slightly proud, and no more.

Common sizes and what they mean

Cylinders are normally sold in five millimetre steps, and the smallest half is usually 30 mm, because that is roughly how much metal is needed to house the pins. So you will see 30/30, 30/35, 30/40, 35/45, 40/50 and so on. The two numbers added together give the overall length, which is what has to span the door plus any plates.

A 30/30 is a 60 mm cylinder and fits a fairly thin door. A 40/50 is 90 mm and suits a thick composite or reinforced door. If your measurements add up to something that is not a multiple of five, round to the nearest available size in a way that does not leave the outside proud, or use a modular cylinder.

When a modular cylinder saves you

A modular cylinder adjusts across a range of lengths rather than being a single fixed size. If your measurement is a few millimetres out, or the door is slightly out of square, or you simply do not want to take the risk on a first attempt, it absorbs the difference. For anyone measuring for the first time, that tolerance is usually worth more than the small difference in price. Our GERDA modular cylinders come in two ranges that between them cover most European doors.

Do I need to measure for a smart lock too?

It depends on which one.

If the smart lock replaces the cylinder itself, like the Smart Cylinder C10, then yes, and these measurements are exactly what you need.

If the smart lock brings its own cylinder, like the Smart Lock SLIM C, you do not need to measure the old cylinder at all. You only need the thickness of the door.

If the smart lock mounts over the existing cylinder, you need to know the cylinder is the right length for the door already, which these measurements confirm.

Send us the numbers

If you would rather not decide alone, email the two measurements and a photograph of the door edge to info@livlock.eu and we will tell you what fits. It takes us a minute and it is free whether or not you buy anything. We would much rather do that than process a return.

Common questions

Which number comes first, inside or outside?

We write outside first: a 40/30 cylinder is 40 mm on the street side and 30 mm inside. Not every supplier uses the same convention, so if you are ordering elsewhere, write it out in words rather than relying on the slash.

What do I measure from if there is a handle plate covering the cylinder?

Measure to the face of the door itself, not to the face of the plate. Then measure the plate thickness separately and mention it, because a thick escutcheon changes which cylinder length finishes flush.

My measurement is not a multiple of five. What now?

Round to the nearest available size in a way that does not leave the outside half proud, or use a modular cylinder that adjusts across a range. The second option is safer if you are measuring for the first time.

How much can a cylinder stick out safely?

About three millimetres. Beyond that a tool can grip it, and snapping an over-length cylinder is a recognised and quick way of forcing a door. It is also something insurers ask about after a break in.

Do I have to remove the old cylinder to measure it?

No. Everything is measured from the single screw in the door edge, with the door simply open. Removing the cylinder needs that screw out and the key turned, and it is not necessary just to measure.

Still not sure what fits your door?

Send a photo of the door edge and the two cylinder measurements. We will tell you which model works before you order anything.